Main Menu
Your Cart

Dr. Pulley Variator Sliding Weight Set 18x14 (GY6)

Dr. Pulley Variator Sliding Weight Set 18x14 (GY6)
Dr. Pulley Variator Sliding Weight Set 18x14 (GY6)
Dr. Pulley Variator Sliding Weight Set 18x14 (GY6)
Dr. Pulley Variator Sliding Weight Set 18x14 (GY6)
Hot
Dr. Pulley Variator Sliding Weight Set 18x14 (GY6)
Dr. Pulley Variator Sliding Weight Set 18x14 (GY6)
Dr. Pulley Variator Sliding Weight Set 18x14 (GY6)
Dr. Pulley Variator Sliding Weight Set 18x14 (GY6)

Description: Dr. Pulley 18x14 Sliding Roller Weight Set for 125cc and 150cc 4-stroke GY6 engines. Dr. Pulley Roller Weights are the latest roller weights to hit the market and the most advanced weights available. These sliding rollers perform up to 20% better than standard round weights and last up to 18% longer with 22% less performance material loss. The weights have several unique features such as their composite material being nylon for faster performance.

Traditionally, the gear ratio is changed by the up-and-down rolling movement of the roller weights in the ramp of the Moveable Drive Pulley (MDF); Now the innovative Dr. Pulley Sliding Roller Weights slide up and down in the ramp of MDF to change the gear ratio. This unique sliding movement (not rolling) provides exclusive advantages to increase CVT performance. With Dr. Pulley, no abnormal wear will occur even when running in high gear.

Dr. Pulley Sliding Roller Weights means better performance from your scooter no matter what stage you are in upgrading your scooter. Simply add 9-grams or 11-gram weights and a CVT Kit, and a new belt for a powerful upgrade. The larger weight size will add top end only when you are doing other upgrades to make up for the loss of bottom or take-off. The same is true for lighter weights, if you go too light you will need to make up for the loss on the top end. 125/150cc scooters we have found do best with 9-gram or 11-gram weights, use 9-gram for over 200lbs. 11-gram under 200lbs. Add the Dr. Pulley variator to complete your upgrade.

Installation: 1. Slack the belt by opening the CVT clutch gives belt slack to the variator side. 2. Then install the variator drive face while lifting the slack belt further away from the center boss if done properly should not see any splines between variator drive face slop-side and boss flat-side. Should be flushed together. 3. Then install the existing variator fan, washer, and hand-tight nut. 4. Finally, apply blue Loctitetorque nut to 30-35ft lbs. For reassurance please consult your manufacturer variator torque specs.

NOTE: Please select weight from the menu.

Features:

•    Broadens your range of gear ratios
•    Fastest Roller Weights available
•    High-Temperature Resistance
•    Increases acceleration and re-acceleration properties
•    Increases top-end speed
•    Lasts longer than standard roller weights
•    Low Friction Coefficient (low wear)
•    No abrasive fibers (glass fiber or carbon fiber)
•    Suitable for aluminum variator housing

Specifications:

•    6x Roller Weights: 18x14mm 7gm<17.5gm
•    U.S. Patent Number: 7,276,004
•    Material: SL-9T, SL-9TS (oil-less PA46)
•    Made in Taiwan
•    Fit Dowel Pin Set (8x14mm)
•    Fit Belt Size: 743835842
•    Fit 54mm Stud Spacing (A-Block)
•    Fit 57mm Stud Spacing (B-Block)

•    Fit GY6 125/150cc+

Supported Models: NCY CVT KIT (Part# 1200-1048-1); GY6 152QMI 157QMJ 161QMK 161QML Chinese Scooter, ATV, Genuine Buddy, Kymco, Polaris RZR 170, Ruckus GY6 Swap, Vento

-----
Item Weight & Package Dimensions:
•    0.092~0.231 pounds | 3.486" (L) x 2.852" (W) x 1.050" (H)

Write a review

Note: HTML is not translated!
Bad Good
Captcha
Dr. Pulley Variator Sliding Weight Set 18x14 (GY6)
  • Stock: 9
  • Part #: 169-218
Sold: 82
Views: 21069
$21.75
Price in reward points: 22

Included